The Ashly FX-125.4 FX Series 125.4 is a multi-purpose installation DSP-equipped amplifier.
The FX Series' pedigree is the culmination of compact Class D design so successfully implemented in the FA Series and Ashly's years of providing easy-to-use software. Along with a newly incorporated DSP engine & software UI, FX takes amplification to new levels. FX is networkable via Ethernet for wired LAN connection, or directly via its built-in WiFi hotspot. No network router needed. FX allows system configurations that don't require additional equipment, such as stand-alone DSP or speaker system processors. All of that is in one box. That saves space, money & time.
With 6 models to choose from starting at 2 x 60W in a ½ RU to 4 x 500W in 2 RU, there's an FX that will fit just about any project. Each offers a healthy compliment of IO (include Digital SPDIF In & Out) and programmable integration ports for remote Volume control, GP triggers and more.
Features
- Offers high power density: 125W x 4 Ch in ½ RU chassis
- Low (4/8 Ohm) or Hi Impedance (70/100V) operation, selectable in software
- Balanced Mic/Line inputs on removeable Euroblock connectors, plus unbalanced RCA inputs
- 2-channel SPDIF Digital IO
- Front panel status LEDs for amp, Input, output & network
- Networkable via Ethernet or built-in WiFi
- Built-in advanced DSP on all inputs & outputs, including: Sensitivity, Routing, Gain, PEQ, Compressor, Limiter, FIR Filters, X-Over, Polarity & Delay
- Browser-based UI accessed via PC or mobile device. No software to install.
- All models have 4 Input channels x 2 or 4 Output channels
- Auto/Manual Power Saver Mode (sleep/standby), adjustable in Software
- Customized Speaker Presets made be created, saved & loaded for each output channel
- Addressable GPIO, Standby/Mute & VC remote ports. VC assignable per channel via software
- ½ RU models easy to hide in "non-rack" installations.
- Highly efficient Class D and lightweight
- Optional hardware for ½ RU models for rack & wall/surface mounting
Specifications
- Channels: 4 x Lo-Z / 2x Hi-Z
- Output Power @ 4Ω/8Ω: 4x125W
- Output Power @ 25V: TBD
- Output Power @ 70V/100V: 2x250W
- Powershare - Across All Channels (up to): 2x250W
- Total System Power: 500W
- DSP: 4 Input x 4 Outputs: Input, Zone, Output & Speaker Processing, plus General Settings
- Networking: Browser-based UI Software with Ethernet & WiFi Connectivity
- Power Consumption: 150W
- Dimensions: 44.5x220x296mm (1.75x8.66x11.65 inch)
- Weight: 2.8 kg (6.2 lbs)
- Output Circuitry: UMAC Class D - Full bandwidth PWM Modulator with Ultra-low Distortion
- Output Voltage: 70 Vp / 140 Vpp (unloaded) // Bridged 140 Vp / 280 Vpp (unloaded)
- Signal to Noise-Ratio: >106 dB (A-Weighted, 20 Hz - 20 kHz, 8 Ω load)
- THD+N (typical): <0.05% (20 Hz - 20 kHz, 8 Ω load, 3 dB below rated power)
- Frequency Response: 20Hz-20kHz (+/- 0.5dB, 8 Ω load, 3 dB below rated power)
- Protection Circuits: Short Circuit, DC, Undervoltage, Temperature - and Overload Protection
- Power Supply: UREC Universal Mains switch mode power supply with Power Factor Correct (PFC) and Standby Converter
- Operating Temperature: 0-40C
- Operating Voltage/Frequency: Universal Mains, 100V - 240V, 50Hz - 60Hz
- Standby Consumption: < 0.5W
- Accessories: Rack Mount Kit (optional) / Desktop Mount Kit (optional)
- Power Ratings: 1% THD @ 120 Vac and 230 Vac
